About: Junk head     Goto   Sponge   NotDistinct   Permalink

An Entity of Type : yago:Whole100003553, within Data Space : dbpedia.org associated with source document(s)
QRcode icon
http://dbpedia.org/describe/?url=http%3A%2F%2Fdbpedia.org%2Fresource%2FJunk_head

A junk head is a form of piston engine cylinder head, where the head is formed by a dummy piston mounted inside the top of the cylinder. In most other engine designs, the cylinder head is mounted on top of the cylinder block. That form has also been termed a "poultice head".

AttributesValues
rdf:type
rdfs:label
  • Junk head (en)
rdfs:comment
  • A junk head is a form of piston engine cylinder head, where the head is formed by a dummy piston mounted inside the top of the cylinder. In most other engine designs, the cylinder head is mounted on top of the cylinder block. That form has also been termed a "poultice head". (en)
foaf:depiction
  • http://commons.wikimedia.org/wiki/Special:FilePath/Centaurus,_junk_head.jpg
  • http://commons.wikimedia.org/wiki/Special:FilePath/Fleet_Air_Arm_Museum._RNAS_Yeovilton._Somerset_(8437697371).jpg
  • http://commons.wikimedia.org/wiki/Special:FilePath/Knight_sleeve-valve_engine,_sectioned_head,_inlet_stroke_(Autocar_Handbook,_Ninth_edition).jpg
  • http://commons.wikimedia.org/wiki/Special:FilePath/Bristol_Perseus_sleeve_valve_radial_engine.jpg
dcterms:subject
Wikipage page ID
Wikipage revision ID
Link from a Wikipage to another Wikipage
sameAs
dbp:wikiPageUsesTemplate
thumbnail
colwidth
has abstract
  • A junk head is a form of piston engine cylinder head, where the head is formed by a dummy piston mounted inside the top of the cylinder. In most other engine designs, the cylinder head is mounted on top of the cylinder block. That form has also been termed a "poultice head". It is obviously essential for any piston engine to seal the joint between block and head. This is usually done by means of a head gasket, a flat gasket on the surface of the block. In early engines, the high pressures and high temperatures made this a difficult trial for the materials of the day and gasket failures were common. The junk head requires no head gasket and is sealed by piston rings inside the cylinder bore, as for the power piston. An alternative solution was the monobloc engine, where the block and head were formed as one piece. This solved the sealing problem, but complicated manufacture and maintenance. Particularly when routine maintenance still required frequent head removal for de-coking, on a monobloc engine this required the removal of the pistons from the crankshaft end beneath. Cooling is difficult with a junk head, with either air or water. Water ports must be connected to the removable head and there is little space available within the cylinder diameter. If the engine uses the common form of overhead poppet valves, these would also be difficult to fit inside the limited space. Air cooling is also difficult, as the shape of the head is deeply re-entrant and it is difficult to arrange airflow to the deep well around the spark plug or injector. Bristol developed a two-part head to address this problem, with copper conducting fins. (en)
gold:hypernym
prov:wasDerivedFrom
page length (characters) of wiki page
foaf:isPrimaryTopicOf
is Link from a Wikipage to another Wikipage of
is foaf:primaryTopic of
Faceted Search & Find service v1.17_git139 as of Feb 29 2024


Alternative Linked Data Documents: ODE     Content Formats:   [cxml] [csv]     RDF   [text] [turtle] [ld+json] [rdf+json] [rdf+xml]     ODATA   [atom+xml] [odata+json]     Microdata   [microdata+json] [html]    About   
This material is Open Knowledge   W3C Semantic Web Technology [RDF Data] Valid XHTML + RDFa
OpenLink Virtuoso version 08.03.3330 as of Mar 19 2024, on Linux (x86_64-generic-linux-glibc212), Single-Server Edition (61 GB total memory, 41 GB memory in use)
Data on this page belongs to its respective rights holders.
Virtuoso Faceted Browser Copyright © 2009-2024 OpenLink Software